Holiday Lights 2

I got the house lights set better on the timer.  They come on at dusk and go off at dawn,  Took a few days of adjusting.  It was so cold the past few nights I had to wear gloves.  Picking out and removing tiny plastic  timer push-ins wearing gloves isn't easy.  But I finally got them right.

The Mews didn't like that I didn't let them outside much the past few days.  Sure they have fur, but it was only 12F when I got up.  I'm not going to let them out in that temperature.  The last time I let Laz out like that, he went up a tree, I fell off the ladder, and I haven't recovered from that yet.   

Seriously, some of the parts I injured then are getting worse lately.  I'm getting to an age where things never quite heal.  The compression knee brace helps on the left.  I walk kind of stiff-leeged these days.  But I think it is getting better.  Some problems heal with time and careful waling.  Stairs are annoying.

So, when I got up and Laz and Lori wanted to go out when it was just 12F, I just laughed at them. 

It was too cold in the house late Christmas Eve,  It actually got down to 8F at one point outside.  We haven't gotten that cold here in over 20 years.

I have 2 digital thermometers that also tell me the outside temp and they agreed about 8 all night.  The thermostat was set at 68F; it stayed at 62.  Even the direct (emergency) electrical heating didn't help.  OK, yeah 62 isn't exactly threatening, but I worried the heat pump was failing.  "Perfect" time of year for that, right?

When it got up to 20F outside, it worked better and slowly got to 72.  8F outside isn't exactly the world's coldest temp by a long shot,  but apparently it defeats my aging heat pump.  I bet it fails soon.  They always fail on the hottest or coldest days...  Calling the installers for a maintenance check tomorrow. They have been good about maintenance before.

Complaining that the heat "only kept the house at 62F" sounds pretty "high-faluting" (I grew up with routinely colder morning house temps as that as a kid in New England) but what I want to avoid is it suddenly being 32F.  The house is extremely insulated and holds warmth, but it loses heat eventually of course.  It's hard to cook wearing a heavy Winter coat and hoping repair people can arrive in a few days...  

Happily, the weather is warming.  Should allow the heat pump guys some days to fix serious other problems elsewhere and check mine out soon enough before it fails entirely.

Hose Repair

I took pictures, so I might as well use them...  :)

One problem with garden hoses is that, if you don't turn off the water, they tend to burst.  I had a 2nd episode of that recently (last one many years ago, so it isn't routine).

I looked out the window a week ago one morning to see water spraying from a broken hose.  I ran out to shut it off of course.  Totally my fault.  

But there are connections to fix such damage and I have a pot of various types.  The usual is a ribbed plastic piece 3" long you insert in the undamaged parts and tighten clamps to seal.

But hoses come in different sizes and I didn't have the right one.  So, maybe off to the DIY store...

Suppose I just considered the cut up hose as "2 hoses" in need of connections?  There are also connections that fix hose ends.  I had a male and a female connector of thge right size for the hose!

So, here is the busted section and the freshly-cut ends to be connected.

I attached the metal male connector just fine, but the female part would simply not push in the other open hose in spite of lubricants and pulling, yanking, and pushing.  

But I had a plastic female connector.  It worked!  

My broken hose now works just fine, 1' shorter.   

Lots Of Stuff

I didn't post here for a while because things got busy.  Part was the stress of the World Series I was sure we would lose (yes, I am a fan of little faith).  Well, optimists may be happier, but pessimists are right more often...

But during that time, I just kept doing small things.

Some may sound silly, but they were important to me.  For example, I painted a broom.  I bet few people have ever done that.  There was a reason...

I loved the bristles on this one broom I had, soft but effective at catching dust.  But the handle broke.  I tried to find a similar broom without success.  So I cut the broken part cleanly and found a PVC pipe that just fit inside it.  I used construction adheasive to join the 2 pieces together.  That failed (I think the adhesive needed air exposure). 

So I drilled holes and put screws in.  That failed too.  The handle stayed wobbly.  But one thing I am is persistent.  I discovered the broom head unscrewed from the handle.  So I brought the broom head to the locval DIY store to see if I could find a matched replacement handle.  None on the replacement handles fit the threaded broom head.

But wandering through the hardware section, I noticed extension poles for roller paint brushes.  They fit!  But the broom head was green and the handles were bare wood or red metal.  I bought the red one.  And spray-painted both the broom head and handle green.

I am insufferably pleased with myself...

A Hard Day

My enclosed garden structure is falling apart.

I didn't think that was possible  because the PVC  tubes were so closely bound by the chicken wire and nylon ties.

But 2 winters ago, enough large snowflakes fell on the top to bend the framework.  It was little enough so that I could ignore it intending to push them straight (there are metal pipes inside the PVC for strength), but I never got around to it.

And a 2nd pvc pipe broke and fell this past Winter. So I went out to fix it.

It was a horrible experience!  Nothing I tried, worked.  You can't be on both ends of a 10' pole at once, but I built it to begin with, so I did in a way.

This is the original framework.  PVC tubes with metal pipes inside for strength...

Not enough strength.  I covered it all with chicken wire. And some large snow collected on it.  I didn't expect THAT.  It bent everything!

One pole just fell.  I straightened it.  And spent 3 hours trying to put it back in place... It was utterly maddening.

I THINK I have the PVC pipe with metal pipe insert cemented into place but I went nuts doing it.  I finally had to cut the chicken wire loose to allow me to get at the PVC connections to push the cemented parts together.  And finally used seriously-stretched bungee cords to keep the 2 ends tight together.

I'll see how well the bonding worked tomorrow.  I'm wondering if I have the wrong kind of cement.  I'll find out tomorrow.  If the parts aren't fused, than I need a different kind that has a primer AND cement combined.

And here I thought I was going to plant spinach, carrots, and leeks today after a small repair job...

Another Day In The Life, Part 2.

So it was Friday.  The mower still wasn't starting.  But the battery was turning over the drive shaft like crazy.  It should have started.  I mean, all that happened was that it was running fine, ran out of gas and I refilled it.

I'm not a gas engine mechanic.  I know the theory better than the reality.  But theory helps.  I can do some simple things.  So after trying to start it again, I went for the basics.  I removed the air filter and beat the dust out of it.  I checked the oil (fine).  I checked the throttle to make sure it was working (it was).  I looked at the manual to see the things that would prevent the engine from starting (blade engaged, brake not on, no gas, spark plug wires firmly attached, etc).  None of those.  Mower just wouldn't start. 

I tried a trick I learned from a mechanic about spraying some carburator cleaner into the carburator and then trying to start the engine.  I saw some drops of gas spitting out of the top of the carburator.  No go.

It was hot and humid and I was getting pissed.  I went inside and made lunch and drank a lot of water.

Later I went back out and asked the mower why it wasn't starting.  I pulled the spark plugs.  They were fine.  Very clean.  No deposits or oil.  The gap looked right.  Put them back in.  I decided the carburator just wasn't getting gas. 

So I took off the gas cap and looked inside.  There was a BUNCH OF DEBRIS ON THE BOTTOM!  HUH?

So I figured I had to get that stuff out.  As far as I could tell, you can't remove the gas tank with out removing the engine and I sure wasn't going to do THAT!  Far beyond my skills.  I was about to try crushing an aquarium net to "fish" around in there to collect the debris, but I remembered a weird little "grabber" gadget I had for retrieving lost screws around engines and under tool benches. 

I grabbed onto the largest piece and pulled it out carefully.  It was a piece of gasket!  I looked at the gas cap and saw it matched a stud to hold the piece.  OMG!  The gas cap gasket broke and fell into the gas tank after I filled it the day before.

I took several more pieces out.  And, to my surprise, some of them were bits of leaves!  I can't figure out how THEY got in there.  Long story short, I removed a dozen bits of junk out of the gas tank. 

So the mower started right up after that, right?  Wrong!  But I'll say one thing for Walmart batteries; they keep chugging.  I got weird sounds, hisses, and a slight thunk.  And all of a sudden, it started.  I was not expecting that. 

And you better believe I drove it all around the yard for an hour mowing the last parts of the lawn short and recharging my brave little battery!  I even got all the grass clippings piled into two 3'wide rows.

That was so I could rake them into piles and cart them to my compost bins.  You can't lay down grass seed on clippings because the emerging roots need soil contact.  I collected 3 trash barrels full of grass clippings. 

Success sometimes comes hard.  A bit of knowledge, a bit of "just trying stuff", a bit of looking for the odd problem, and a bit of luck makes a difference.

Now all I have to is rough up the bare spots with a rake and spread the grass seed all over the lawn.  I have fescue grass here.  It clumps rather than spreads, so it needs to be reseed every few years to stay looking full.  But it is a vigorous grass.  Bluegrass would look nicer, but it gets too hot here and I don't get enough sunlight for it.  I spread a sun/shade mix of tall turf fescue when I renovate.

And I read up on the procedures each time I overseed, just to make sure I don't forget good hints.  Apparently, my experience is better than many internet sites, because you wouldn't believe some of the nonsense I read this week!

And THAT is tommorow's post...

Getting Busy Again.

I got at the rototiller, mower and snowblower yesterday.  None of them would start on the previous day's try.  I tackled the rototiller first, since I had an immediate need for it.  There was gas.  The spark plug was clean and dry, the air filter wasn't clogged with dust.  The wire controls at the top were moving levers down below.  No reason I could find  that it wouldn't start.  I had started it right up last year and it had been sitting around for several years with old gas in it then.

So I tried this trick about leaving the air filter off and spraying carborator cleaner insidethe exposed carborator, waited a few minutes to let it dissolve old gas, gave it another spray for fuel, and pulled the rope a few times.. It coughed, sputtered as I tried to adjust the choke, and died.

But that was better than before!  So I gave it another spray of the cleaner stuff and it stater again.  And died.  Took 2 more tries before I get the choke adjusted to keep it running and then it purred like a kitten.  Well, OK, its not a quiet machine.  I sounded like a congested bear snoring in hibernation.  But you get the idea.  I used it immediately!

Wheeled it to the big bulb bed, set the manual depth at 3" and went through the weed/grass roots easily.  The occasional baseball-sized rock made it jump around a bit, and I had to make sure it didn't till down too deep (I was going over some existing bulbs).  Took only 15 minutes, but that beats at least and hour on manual spade work. 

I raked the area and was pleased to see no bulbs dug up.  I knew where they were generally.  I planted then from the outside edge inwards, but I hadn't marked there they stopped.  Fortunately, I have found a couple of good pictures, so I can estimate where to plant the additional ones this year, but that's anouther post.

So, encouraged by getting the tiller running, I attacked the mower.  I was in trouble from the start.  There is a hollow rubber priming button you push 3x to get some gas into the system.  I pushed it in, and it wouldn't come back out.  UH-OH!

Well, I then tried all the same tricks as with the rototiller, but it wouldn't even cough and sputter.  It had to go to the repair shop. 

So I checked the snowblower.  It has electric start and it wouldn't start.  I checked the spark plug, I checked the air filter.  No problems.  Sprayed in some carburator cleaner.  No luck.

What is the first question the computer repair guy asks?  "Is it plugged in"?  Well, I checked the gas tank.  Bone, dry, clean.  Not even dried old gas.  I must have done what "they" always tell you to do with seasonal equipment; drain out and or absorb it out with a old clean towel, then run it until it stops.  No gas left; no bad gas left.

So I added a cup of gas, started right up!  I let it run for a couple of minutes out on the driveway.

2 out of 3 ain't bad!  

Tomorrow:  Two errands in one trip!

Bathtub Area Replacement

First, getting up at 7 am to be ready for the demolition crew was a novel experience.  Second, getting the cats stashed away into a safe room was only a partial success.  Third, no renovation work ever goes smoothly.

I managed to get up on time, fed the cats, and went to get them into the bedroom.  I called them and Marley and Iza came right in.  Ayla was not so cooperative,  sensing that "something" was up.  I know better than to chase a cat, I just follow slowly.  But she was ducking from room to room and upstairs/downstairs until she was upstairs and I wasn't sure where she was.  I figured she was either in the Mews Room or the Computer Room, so I just closed both doors.  It turned out she had to be hiding in the Living room somewhere.  I swear that cat could hide in a coffee mug!  But since she stayed in hiding and didn't try to run out through the frequently opened front door, all was fine. 

The bathtub area demolition was impressive.  I took a LOT of pictures for possible insurance reasons, but I will only inflict a few of them on you.

The before shot shows the mess.  When the tiles began to come loose, I duct-taped plastic around the front and side, not realizing how bad it was getting behind the plastic.  And under that situation, tub-cleaning seems to have fallen off my schedule.

So, they went in and just started pounding the tiles and backer board into pieces.  Well, the plastic was more waterproof than the tiles were!

Bathroom renovators are notorious for finding "more repairs needed" when the backer boards are removed.  These guys said everything looked mold-free and no rot.  I looked at it and agreed.  I don't know tiles, but I know about wood.  So they vacuumed all the dust and debris.

And started to replace the backer board.  It is a special concrete and laminate product that basically can't rot.  So was the original stuff, but after 30 years, the modern product is better.

Next, they installed the new tub and covered the inside with padding and plastic.  And it was a good thing they did!  Because after that, they constructed and installed the new pipes.  I wasn't thrilled to see them using a plastic pipe, but they assured me that it is better than copper pipe.  "Not one failure in 10 years and it sheds mineral deposits that can collect in copper pipe with hard water".

Well, I have soft water, but if the cemented plastic holds better than soldered copper, OK...   BTW, the first day I moved in here 30 years ago, I tasted the water and decided it was the best municipal water I had ever tasted!

So then we had a few "adventures".  The first was a pipe cap blowout.  You see that copper pipe sticking out over the tub?  There is a temporary pipe cap.  The Senior Repairman said they are called "shark valves" because once on, they never come loose until you want them to come loose".

So guess what came loose?  Right!  The shark valve...  The assistant went running to the door shouting at Senior guy that "the water is on".   Well, yeah, it had been turned back on, but I realized he suddenly didn't WANT it to be on, so I ran into the basement (bad knee and all) and crawled into the access where the whole-house shut off valve was and closed it.

That apparently saved about 50 gallons of water pouring out the open tub into the basement.  And I stuck a bucket under the leak. 

They were very apologetic.  Those caps "never fail".  Well, until they do, of course.  At least I got some credit for fast-action!  The assistant is not the brightest bulb in a room of lamps, he meant "water is flowing and it shouldn't".  I had noticed the senior guy mad jokes about the assistant (his BIL) and I had joined in slightly, but I stopped after that.

But, no harm was done.  The plastic in the tub caught most of it and my bucket caught the rest.  The senior guy was really pissed off, but I joked "that was fun, let's do it again". 

After they vacuumed up the water and replaced the plastic lining with a dry one (and made sure I saw they were using a brand new pipe "shark valve" cap), they proceeded with the job with the water turned back on. 

Then the second little "adventure"...The last backer board to be installed was the one that fits over the tub faucet and shower valve.  That takes very precise cut-outs.  And senior guy cut it wrong!    Oh wow, did the assistant have a relieved turn with that.  I had noticed the the senior guy just wrote the cutting dimensions randomly on a piece of paper.  Well, I suppose when you have been doing something for 38 years (as he said he had), you know where your numbers are. 

Oops, he got the left and right measurements reversed..  No problem for me, it's a fixed price contract (and the senior guy did mention that it comes out of company expenses.

I mentioned to him that when I put wood paneling in the basement, I had been careful to use a huge piece of cardboard from a bookcase box to make sure I cut it right.  Ans then traced that onto the wood paneling so that I COULDN'T get in wrong.  And got it wrong ANYWAY because I put the cardboard on the wrong side of the panel.

True story, but it did lighten up the situation...  The last thing I want are angry embarrassed workers doing work in my house.  I've done enough house work myself to know that when you get mad, you don't do your best work! 

So senior guy cut out another concrete backer board panel and it fit like a glove. 

They return on Monday to install the bathtub fixtures and do the tile installation.

Ayla, Iza, and Marley recovered quickly.  Food helped, attention helped, deck time helped.  quietness helped.  But I bet I will have to get sneakier about getting them shut into the bedroom Monday morning.  At least the final work is quieter...

The Heat Pump...

The repairmen came, they went.  In their wake, they SEEM to have left me with a working heat pump.

I was worried when the repairman showed up.  It was the same guy who messed up my system in Feb.  While he started working on the unit, I called the office repair manager.  He called back a few minutes later to assure me that the guy he sent was especially good at replacing parts.  But also would come by in 30 minutes (from another job) to make sure all went smoothly.

And it was a damn good thing he did.  Because the repair manager had to do most of the work himself!  He had promised me a free part and free labor, but I did not know the free "part" was almost the entire inside unit.

It took them 4 hours.  Because of some gradual equipment changes, the replacement coil was not a "pull and replace" unit.  The manager went "hands on" to it, cutting some sheet metal to fit.  I got a kick out of saying to the sent repair guy "This is why I worked to be Manager, so as to not have to do this stuff".

The "sent" guy would not have known to do that shaping work.  If I hadn't called, he might STILL BE HERE 6 hours later botching the job.  And that is a lesson learned.  If a simple repair is done right, great.  If a complicated repair is done well by a talented repairman, great!.. But if a repair is in the middle and they send the simple repairman to fix it, you need a Manager!

And did this guy know his stuff!  It was like watching a surgeon.

And it got better!  A few times when he was waiting for equipment to provide results, I asked a few questions.  Apparently, they were good questions.  Having a Dad as an engineer helps...

So I mentioned understanding gas expansion cooling, and he mentioned that he had taken AP classes in physics, so we had a great discussion about dark matter and dark energy and fun stuff while his equipment measured pressures and temperature changes.

Geez, I hope managing a heat pump repair unit pays well...

Anyway, the high pressure whistling sound is gone inside and out, the screeching sound of the outside fan is gone, the heating and cooling seem to be working, and all I had to pay for was the coolant.

I hope I feel as happy in mid-summer and next winter!  The repair company maybe doesn't have the best basic repairmen, but they sure stand by their promise to make everything right eventually.  That sounds like a back-handed compliment, but I mean better than that.  They COULD have just fought my complaints and said go call someone else if I wasn't happy, but they didn't.

It was 70 degrees outside.  They heated the house up to 80 and cooled it down to 65 in just an hour.  AFAICT, that means it is working.

And BTW, Iza is a Very Brave Cat .  She followed us all around, watching what was going on.  Marley an Ayla hid in the bedroom.  Iza got extra treats after they left.  She is a "Snoopervisor Extraordinary"!

Cat Tree Repair

A few months ago, the tallest platform on one of the 2 cat trees came loose.  Its the one that Ayla and Marley use to jump up to the top of the nearby bookcases, so there is sideways pressure going up and down.  I discovered it was attached with bolts through plastic disks in the post and the plastic had broken at both the top and bottom.  I thought about attaching blocks of wood in the post, but that seemed like a weak repair.  So I searched for a replacement post.

The manufacturer of the brand didn't seem to sell replacements, but I found one at another brand's site.  Assuming they were all the same, I ordered one.  It arrived.  With a block of wood in the top and bottom of the post, LOL!  And the wood stuck down out of the post slightly,  which meant it would wobble a bit no matter how tight.  But it also had a long skinny bolt sticking DOWN several inches and a smaller one sticking UP an inch.  Well, that was no good, either bolt would injure the cats.

So I complained to the seller and demanded a free return label.  They just credited my card instead.  Fine.  I just ignored the whole problem for a while.

A few days ago, I got back at it.  As awkward as it was to do, I got both bolts out and drilled the holes larger to fit the original bolts (which were flush to the surfaces and capped with protective plastic caps).  Then I clamped the post in a bench vise and planed the wood blocks flush with the surface.

The original bolts had little hex-shaped indents for tightening with an allen wrench, which holds well but can be difficult to turn.  But I got that done eventually, and the platform was re-installed nice and tight!  Hurray!

Rain, Good And Bad

Well, we got some heavy rain here Tuesday.  Almost 3" all day, but almost all of it in 1 hour.

I'm not going to complain bout it much.  I needed some rain.  It hasn't been as dry as in some years when the soil cracked open, but on the other hand, the soil surface and grass was dry this afternoon, so I mowed the lawn.  Other places got more rain though, and not the kind that would just get soaked up by the lawn.  Places in Maryland got 9-10", and In New York, it got up to 14".  I saw pictures on TV of cars floating around in streets and parking lots.  So it could have been a LOT worse here.

Still, I had some problems with water getting into the basement, and I thought I had solved that with the extra-large raingutters installed 2 years ago and a drainage ditch I dug from the sunken patio.  The sunken patio has been a problem for a decade at least.  It properly slopes slightly away from the house.  The water that collects at the lower end for a day or 2 is a minor (but annoying) problem.

It's the fact that the lawn level has raised over the years that really creates the problem.  Grass grows, I mow it, the clippings become topsoil, etc.  Well, that's why praries have dozens of feet of topsoil.   I need to lower the lawn level at the edge of the deck, but that is back-breaking work and I keep avoiding it.

Instead, I dig a drainage ditch.  3"wide, 3" deep, and the lawn slopes downhill from the patio, so it works great.  It can drain off even the heaviest rain.  The problem?  Soil moves.  The ditch slowly fills in very slowly and I never notice when it is QUITE not capable of handling the occasionally heavy rainfall.  So I have to run out in the downpour and rescrape the ditch with the grubhoe deep enough to drain the patio.

But I had an additional surprise this time!  The raingutters ARE working just fine.  But, apparently, the soil level raised just enough this Summer to direct the outflow back toward the patio instead of out into the downslope lawn.

I'm generally an optimist (though maybe not a rational one).  I always expect things I fix to STAY fixed.  To show the flaw in that, I also expect weeded areas of the garden to STAY weedless, repaired cars to STAY working, and structures I build to stay standing.  Obviously, there is a flaw in my expectations.

So when I dig a ditch to drain rainfall away from the patio, I expect it to STAY a ditch...  Even though I'm the smartest person in the house, I have some errors in my assumptions.

So I'm going to fix this rainfall-in-the-basement problem once and for all!  I'm going to build a sealed 1' dike in front of my basement!  Just kidding... 

Seriously, I'm going to lower the lawn level 3" below the edge of the patio/lawn.  I will dig a 1' deep trench along that edge and toward the downslope lawn, and I will install perforated drainage pipe buried in sand and landscaping fabric (however it is recommended).  And I will attach a 4'  extension to the existing downspout to get the rainfall from the roof away from the patio.

Drainage pipe...

Gutter extention...

 

Trailer Rebuild, Part 2

So there I was, back to the original framework (except for having some holes drilled through the metal - I tell you those step-bits for drilling metal are great)!

It was time to put on the new stuff.  I had decided to raise the sides from 18" to 24".  Most of the material I want to haul these days is fairly light - mulch and compost and tree debris.  And if its heavy (like sand) I'll just keep the load below the metal framework.

First, I bought all new stainless steel bolts, nuts, washers, split-washers, etc.  And a special purchase I will mention later.

Then I started with a solid floorbed.  No more tarps of the bottom to damage when I shovel material out of the trailer.  The side there is merely clamped down to hold the bottom sheet in place and to see how it would look.

One single 4x8' sheet and then custom fit strips off a 2nd sheet because (surprise!) the trailer is off square by 1/4" and I didn't want any gaps.  I got that strip so accurate I had to stomp it into place!  And then I couldn't push a fingernail in anywhere along the length.  Given a long history of bad circular saw cuts, that may be a personal "best".  It helped that I used a neat clampable straightedge tool (and measured 3 times before cutting).

Here is the clamping straight edge.  It comes in two 4' lengths that can be connected to 8'.  Very nice for cutting plywood!  Mark the cut line and then 1 1/2" more (for MY circular saw - other brands may vary) and it's hard to go wrong.

So, with the bottom in place, I could attach the sides...

Since the sides stick up higher than the metal framework, they need some support.  And the back is designed to be supported by 2x4s sticking into those small frames you can barely see on the back.  They work, but they don't quite fit 2x4s; you have to plane or cut them at th corners.  but I want better support at the top of the back anyway.  And I don't like the exposed edges of the P-T plywood.

So I will show part 3 when I figure out the details.  I know WHAT I want to do, but the measurement tolerances are tight so I may think about it a couple days.  But if what I have in mind works, you'll like it.

Trailer Rebuild, Part 1

I love my 5x8' hauling trailer.  It transports mowers, hauls sand/mulch/compost home, hauls tree debris/recyclables/trash to the county landfill, and I bet it would carry a dozen neighborhood kids on a joy ride for a dollar each (just kidding).

The thing has an open metal frame, so I had to built plywood sides when I bought it.  Ten years+ later, the sides are rotting away.  And the base is boards with spaces between them, so I've always had to put a tarp on the bottom to keep small stuff like sand and compost from falling out (and a tarp above to keep it from blowing away).

So it was time to rebuild!  This time, I wanted rot-resistant (and higher) sides, a solid bottom, and more attached (but still removable) back.  When the trailer is off the car, the front sits on a cinderblock so it tilts back (no worry about rain collecting inside). 

So after sketching out various trailer side and bottom dimensions, I took the trailer to Home Depot (I needed it to haul new plywood home).  I went for 1/2 pressure-treated (P-T) plywood 4x8' sheets.  Home Depot changed a "no-cutting" policy on P-T wood last year or so to allowing it.  They have a great sheet plywood cutting machine, but it's one free cut per sheet.  I had fun figuring out the cuts (no seriously, I had FUN figuring out the cuts - I was good at geometry in school and I do some slight wood-working).  I figured out a satisfactory way to do the whole thing with 3 sheets of plywood and only 1 Home Depot cut on 2 sheets.  I would have had them do a cut on the 3rd sheet, but I needed to custom fit that cut.

Here are the BEFORE pictures...

You can see the sides were falling apart.

So I unloaded the new pieces.

And set about removing the old...

Easier said than done!  Some of those zinc-coated bolts and nuts were locked in place.  Considering that some of them just loosened and fell out over the years, that was a surprise.  (And for those of you in the know, I used lock washers and double nuts on all the bolts)

Thank goodness for Liquid Wrench!

I soaked all the nuts with that.  They still fought, but they DID all come loose with "persuasion".

And eventually, I had all the old sides removed.

Next time, I put on the new bottom and sides...

Marks (Murphy's) Law

I love my riding lawn mower.  But it seems to develop a new problem every Spring.  This year the choke knob broke off in my hand.

I'm one of those people who NEVER have normal problems.

My "Top 30" plant provider sent me the wrong plant 5 years ago and it turned out to be "wickedly invasive".

My twice-spayed cat STILL goes into heat.

Any repair problem is "Wow, I've never seen THAT happen before.

My "Murphy's Law" event is what "Can't happen",  does.

So, naturally, the choke knob problem was "that doesn't happen".    Well, it did.  I pulled the choke out as usual a few days ago and the shaft snapped right off.  I could feel it.  And it just came out loose when pulled.  You can't start an mower that needs the choke adjusted when you can't adjust it...  I felt around inside the engine compartment to see how it was attached, but couldn't see a clue to how to get at it.  It turns out later that the entire gas tank has to be removed.  "Not something I want to mess with".

So I called a guy who will come and fix mowers on site.  I've used him before.  He does good work and is honest and his deal is "fix on site".  But to be honest, he usually has to take the mower away.  But at least he will do that.  He did something neat that I will have to remember.  He bypassed the choke by spraying carburater cleaner down the removed air filter!  That primed the starter!  Hey, I didn't know.  Maybe you did.  LOL!  I'm a gardener and woodworker.  When it comes to engines, I'm lost.   I have 2 gas chainsaws in the basement and I can't make them stay running.  That's why I have an electric one.  It always works!


So he started it right up (Starting the mower was not the problem when the choke lever worked) and drove it onto his truck.  If I had known that trick before he came, I would have mowed the lawn first.  It is already 4" high and growing.  When I get the mower back in a week, it will be 6-8" high.  This time of year, you CAN actually watch the grass grow!

Been Busy, But Not Anything To Show

Sorry I haven't been posting with new projects lately, but the stuff I've been doing lately hasn't been exciting or photogenic.

Laying down limestone to increase the lawn pH doesn't show up in pictures.  Taking down the cages with the dead tomatoes isn't much to brag about.  Washing the windows outside and in is nice, but you can't tell anything from a photo of them.  I spent a hour cleaning fallen leaves out of the boat before I "shrink-wrap" it for the Winter (whoopee).   I even spent time scraping 20 year old paint off the garage door glass panes!  Talk about a task put off too long!  LOL!

On the other hand, some of the non-visual time has been spent considering what to do with the decks.  I have an upper and a lower deck.  It seemed a good idea at the time, but quite frankly, the larger lower deck was a complete waste of time.  I have never had any use for it.  Well, OK, its a convenient landing for the stairs from the upper deck and then to the lawn.

So I'm going to take it apart and use the well-weathered-but-still-sound 2x6x12' decking boards to rebuild my framed garden beds.  The deck boards (not in ground contact) are in much better condition than the 2x4 garden boards after 20 years.

After the lower deck is removed, I will renovate the upper deck.  The frame is sturdy (but not to "code"), and the deck boards and rails are wearing out gradually and finally warping a bit.  The 2x6 boards are fine to frame garden beds, but they will soon be a question to walk on.  And the rails were always ugly.  Rail fence style.  So I will redo the top.

I plan to rebuild the top of the deck in the same style as current.  Except, the spaces between the upper posts will have a sunburst design I can easily make myself.  What can I say, the deck needs an artistic touch.

And I want to make the patio below the deck rainproof.  Well, at least "mostly" dry in a storm.  I know a serious rain can get in at the sides no matter what I do, but I (or the cats) don't plan to be out there in THAT kind of storm.  I just want to be able to sit on the patio under the deck in a normal drizzle and not have the rain falling through the deck above.

I initially thought of removing the deck boards above, covering the joists with pressure-treated plywood, roof felt, and 5/4" deck boards.  Reading a few DIY sites convinced me that was a bad idea!  So I am going with an under-the-deck system.  I've figured out I can attach a sloped wood frame topped with ribbed plastic panels UNDER the deck!

I have been standing on the patio figuring out how to attach the wood support frame in a way I can slide the plastic panels onto it.  It will be awkward to do alone, but I'm kind of used to that.  When I initially built the deck, I had 2 friends to help.  One moved away, and the other has a bad back now.  And I can't do what I used to do either.  Getting old is hard...

But I think that is all for next Spring.  For a temporary thing, I am going to hang a tarp under the deck to see how that works.  I can do that in a day.  And I'll take pictures of that.

The laugh is I'm only trying to make the patio dry so I can put vinyl fencing around the patio and let the cats out there...

Thanks for coming by to read...  :)

Asparagus

ASPARAGUS!  I have an 8' by 3' asparagus bed.  I'm proud of it.  I harvested over 60 spears this year before letting the plants grow to replenish for next year.  It was great!  Last year I barely got a dozen (and they were late to emerge) and I thought they were dying.  I LOVE asparagus!  Fresh asparagus tastes better than grocery store ones!  And they are tenderer while still crisp when steamed...

I started with 10 crowns 15 years ago, but am down to 7.  I should replace the lost ones.  Or maybe I should just replace them all this Fall.  I haven't decided.  2 years ago, I covered the entire bed with black plastic to kill all the weeds.  That didn't work.  The weeds survived and the voles went crazy under the safety and warmth of the black plastic.  They killed several crowns entirely and damaged others.

But because I wasn't sure where the new spears were emerging (so I didn't want to chop them with the shovel) and didn't want to dig weeds out around the bed, the weeds are taking over.

Anyone want to come over and weed my asparagus bed?

I seem to have a lot of tree saplings and grass...  Yes, they grew THAT high just in this year!

Well, when I dig all the saplings and grass clumps up, I will do what I USED to do that helped.  Place folded up sheets of newspaper between the asparagus stalks.  It works great.  I just kind of overlooked it the past two years...

Small Pond

Small Pond looking GOOD!  I attacked the overgrown roots and cut them back to pot size.  That was massive work  It took all my effort to haul the huge root balls out.
.
 First, mud and roots...

I scooped it out wearing large water proof boots.

With the newly cut out pieces removed and chopped, I replanted the pond with pots....

Repotting the pieces of plants took serious cutting apart of ingrown roots.

And weighing the pots down with stones took some work.  I had forgotten the pots fell over when top heavy.    But I got it all right eventually.  It looked good at the end.

The lilies will take 2 months to recover and the sweet flag will take a month.  But at least there is room again for the goldfish to swim around.

I'll wait a week for the water to lose the chlorine from the new water again before adding goldfish.  But I will do that.

The pond will be so nice with a few goldfish in it. again.

Serious cleaning-up to do.  See all the excess roots?

All the excess leftover roots would fill the whole pond...

Computer Problems

3 PM:

My Mac Pro computer is apparently too evil too repair.  I don't mean that it is possessed with a malevolent spirit or that there are problems that multiple repair techs can't fix.  I mean that it apparently smells so strongly of cigarette smoke that no one is willing to repair it.

OK, I'll say straight off that if the computer is damaged because I smoke, that is mostly my fault. Only "mostly" because I have a lot of other computerized equipment in the house (including a PC that worked for 8 years - and still does) and they all work just fine!  The Mac needed repair after only 9 months and then again after 6 months.  If Macs need to be operated in a smoke free "safe" environment, they should have told me! 

I am not defending smoking; I know it is a really dumb habit and I'm trying to quit .  But when Apple Repair Stores point to "environmental abuse" in the warranty and claim that detectable cigarette odors void the warranty, I have a right to think I am being abused...

I was surprized and confused when the 1st repair place refused to work on the computer.  I tried to find a place that cleaned smoke-damaged computers (with no success).  When I called an actual Apple Store, the person laughed and said of the 1st repair place - not an official Apple Store, "That's just an excuse they use, bring it in and we'll repair it".  I was quite relieved.  But after 3 days, they called me back with the same story; that they wouldn't even work on it and my extended warranty was void.  Apple considers cigarette smoke to be a "toxic hazard".

After struggling with the fan problem for 3 weeks plus driving 220 miles back and forth to the 2 repair stores AND not having a repaired computer, that was a hard blow!

The problem is that the output fan operates on high speed constantly.  The computer appears to work just fine.  So it may be that I just have to put up with the noise until I can find someone willing to clean/repair it.  Or I may have to replace it, and quit smoking.  Quitting would be a very good idea anyway.  And I think I bought way more computer than I need, so replacing it may not be THAT expensive, especially if I am no longer buying cigarettes.

So the computer might fail at any time and it will be a while before I can replace it...

Update:

I just searched "Mac cigarette smoke" and found many sites that explained why cigarette smoke is so damaging to computers (and especially Macs because of their design).  I understand now why it is a real problem.  I even found a discussion site about it.  There were posts from users in my situation, users who have never (like me) experienced the problem with a PC, posts from users who blame Apple for not specifically mentioning cigarette smoke as a deal-breaker, and posts from Apple techs who described how cleaning melted nicotine from computers is both nearly impossible AND disgusting (even to techs who smoke).  Apparently, no smoking user has ever gotten any mercy from Apple.

I am in a real dilemma.  Given the descriptions of the problems with repairing Macs abused with cigarette smoke, I accept their refusal to repair the computer.  I think Apple is seriously wrong not to advise buyers that smoking voids the warranty or extended warranty, but I accept that no further action on my part can get the computer repaired.

I am fairly confident that I could stop smoking in order to save the next computer (if not myself).  But I haven't really been happy with my Mac Pro.  I haven't had crashes like on my PCs and I feel little threat from hackers, viruses, etc, but the applications software basically SUCKS!  Pages and Numbers are far less featured that Windows Word and Excel.  Even Office for Mac is far less than the same on a PC.  Organizing files in Finder is much harder than in Windows Explorer.  I first thought I just wasn't familiar with the Mac systems and commands, but after more than a year, the same problems remain.  Macs are expensive.  In addition, the nearest Mac repair store is 25 miles away, while there are 4 PC repair stores within 3 miles.

On the other hand, I switched to a Mac because Windows became so frustrating to use.  It crashed, it froze, it needed massive hacker and virus protections, and it is slow to load software.  The 3rd time in 1 year that I had to spend 2 days completely reloading all the software from scratch made me determined to never own a PC again.  My PCs needed a repair about every 6 months.

I think, though, that I will stick with a Mac.  My old PC still works.  I could use that more often for offline work.  As far as I can tell, my Mac would not yet need any repair service.

If that forces me to stop smoking, it might be the best purchase I've ever made!

The Heat Pump Works!

OK. It seems like the heat pump guys finally got the thermostat to communicate with the heat pump. It wasn't easy, though.

At first, they insisted on trying their standard thermostat with their standard heat pump for 3 days in a row and it didn't work. The 4th day, the same repair guy arrived with a 2nd repair guy who claimed to have had these problems before and solved them. I was getting pretty tired of all the failed attempts and told them that they either fixed the problem or haul the unit away, reimburse me the whole cost, and I would call another company. Not to my surprise, that seemed to have an effect...

1. I had looked up the Ruud brand of heat pumps on the internet last night and they are not the best. Well, I had heard of them for years and thought they were good. I only chose them because it was so hot in July when the York unit failed, because York said "2 days" and Ruud said "1 hour". At the time, I was desperate; it was 95 in the house!

2. I hoped they (Ruud) would take the unit away so I could change my mind and get a Trane.

3. I didn't think that a different thermostat would solve the problem.

Well, damn, they seem to have fixed the problem with a different brand of thermostat! And while I an not a thermostat expert, I listen carefully and learn well...

We know we see integer degrees on our thermostats. We see 71 or 72 or whatever. It seems that thermostats don't actually function in those terms. They can measure full degrees in full whole numbers (71, 72) or half numbers (71.5) and that is promammable. They thought that might be the problem for over an hour. IOW, the problem might be that that the thermostat was reading full degrees when it should be reading half degrees (something about both heating and cooling reading the same units that caused the problem). But changing that didn't solve the problem anyway.

Finally, they just hooked a different brand thermostat in and it worked perfectly right from the start!

Can you believe that? They fought with a thermostat they knew they were having troubles with and that wouldn't work for three days (they had tried 4 new thermostats). Sure, they wasted their time at it, but they wasted MY TIME, too. The time while they worked and the time I waited. I figure I spent 20 hours this week either waiting for them to arrive or watching them while they were here.

The good news is, that after 3 days, the system seems to be working properly, I have gotten used to the thermostat controls, and the whole house breaker has not tripped once (isn't that curious). That whole house breaker box problem started when the heat pump went bad and ended the day it was fixed (so far). That the heat pump guys say it couldn't be their fault means nothing to me. I'll take coincidence on this matter.

I am quite certain that, somewhere, there are people with the bad combination of the particular thermostat with the particular heat pump from this company who DON'T know their heat pump shouldn't be running all the time and wondering why their electric bill is high.

When I suggested to the repair guys that they should have the company backtrack these situations, they just laughed while walking out the door. A case of "not their problem", I suppose).

Well, mine is fixed... Maybe I should only care about that. But I don't... I think I will email the Jiffy company (the installers) and raise the issue.