Pictures

The ivy cuttings...

The spider plant that was a few dying leaves pinned with a tent peg in March...

The snake plant pot I need to divide, but can't pull the rootball out of...

Ah, the "Comfort Station"...  I never used to drink cocktails until Dad moved in with me  in 2012.  He loved Martinis.  I could never stand such pure stuff.  But I found fruit-based drinks to accompany him.  

My favorite is a "Gin Buck".  Sling glass with 4 ice cubes.  1 oz gin, 1/2 oz of lemon juice, fill with ginger ale.  2nd is what I call a "Peach Comfort".  Sling glass, 4 ice cubes, 1 oz Southern Comfort and 1/2 oz Peach liquer, filled with ginger ale.  3rd is what I call a Cavebear Sling.  Same glass and ice, 1 oz of gin and 1/2 oz of Pomerganate juice.  Tart.  I drink them all with a straw.  Purists would wince.  I like it because I drink it slower.  I can't just "sip"...

There is bourbon and vodka in the back for odd variations, but I seldom go there.  Vodka is just for getting drunk and that's not my interest.  Bourbon is for visitors who like it. 

And I have 2 glasses of Zinfandel wine with dinner.  The White wine is for spicy chinese dinners.  And I eat dinner slowly, so the wine goes slowly.  I'm retired, who cares?  LOL!

Catching Up

It is supposed to snow tonight.  At first, the forecast was for 1-3", then 2-4", then 4-8".  So Winter starts...

I spent the past 2 weeks getting the yard ready for Winter while the temperatures were till in the 50s.  Mostly small stuff like pulling out the dead tomato and pepper and corn plants.  Harvesting the last of the carrots and celery (leaves only here). 

But a few major things.  I have 2 toolsheds.  One is 25 years old and a tree fell on it about 5 years ago.  Poked a few holes in the roof.  Which didn't matter much since I didn't put anything under the leaks.  But I replaced the shelves and wanted to use them, so I slipped new shingles over the holes.  That didn't work. 

The roof needs replacing, but I didn't have the time.  So I screwed on a piece of 2'x8' plywood over the holes and caulked around the edges.  That will work until Spring when I can replace the entire roof. 

Two toolsheds may seem a lot (both 8'x12'), but I have a lot of equipment and a dislike of having to move 4 things to get at one).

I put a bag over the new metal hose reel.  The manufacturers say the powder coating should last many years, but I think protecting it in Winter will make it last longer, so why not?

I had black plastic sheeting covering the 30' round bulb bed all Summer to kill weeds and keep the bulbs dry (bulbs like dry soil).  It was pretty much used up and brittle, but I spread it out off to the side and cut it into pieces.  I folded those up 3x to make some weed and grass smothering over winter in the flowerbeds.  Come Spring, I should have no weeds to fight with when I want to plant annual flowers.

I also used some to cover the garden paths.  They are paver squares on gravel, but weeds even grow in THAT, but they won't do well covered for 4 months.  With luck, the paths won't have weeds to fight with in April.

I also pruned briars to the ground.  They thrive here with the least bit of inattention and I was very inattentive this year.  I can only do so much.  Cutting them back will cause the roots to diminish (not being fed by the leaves) and digging them out next year will be easier. 

I filled the trailer with plant debris too tough to compost (thorns seem to survive forever), and planned to bring them to the County Brush Composting site (where they can get huge piles that even decompose thorns) last Saturday (the only day they operate November though March) but I stayed up too late and is is going to snow tomorrow.  Figures...

I'll get there tomorrow if the snow fails or next Saturday.  Between 7:30 am to noon, I can get a free load of mulch in return for the debris.  I'll spread it over the bulb bed to keep down the weeds.  Actually, I think it will take 3 loads to make a 3" thick layer, but I can manage that even in cold weather.

I have 2 large pots of Snake Plants.  I took one rootball out and divided it into pieces.  The plants grow thick tangled roots and are not easily separatable, so I just cut them apart with an old serrated Ginsu knife and put the best pieces in eight 6" pots with new potting soil.  They are slow-growing and have energy reserves in the thick roots, so I won't know if they are growing until I see new leaves probably in a few months.

Meanwhile, I have another pot of them in a wide shallow ceramic bowl that I can't pull the plants out of.  I'll try soaking the pot in a large bucket for a few days, but I expect I'll have to break the pot to get at the roots.  I have a very useful plastic container 2'x3' and that will help.

I took some variegated ivy that were in small 6-pack cells all Summer and grew long stems while I wasn't paying attention.  I cut the stems of one into short sections to make more, and I set the others into 4" pots in new soil.  I may end up with a dozen ivy plants.  I'm thinking of hanging a pipe from the ceiling and supported a 6' planter box of them from it to make a "waterfall" of them.  Watering could could get drippy, so I'll need a shallow box below them.  I don't know of a product like that, so I'll have to build one.

The 6 cuttings of my original Waxy Hoya plant all seem to be rooting well, and I'll need to find a place for them too. 

Between the Waxy Hoyas, the Snake Plants, and the Ivies, I need a lot more light.  In Spring to Fall, some can be out on the deck, but Winter is a problem.  I think I need to make another light stand designed for tall and hanging plants.  Well, that will give me something to design and build over Winter.

And that doesn't count de-clutterring the basement.  With the old toolshed secure from rain (I hope, and am waiting to see), I can move a lot of stuff in there.

With more basement space free, I can get at the regular Winter project of making new starter/potting soil.  I like making my own.  It's cheaper, but I also get to make it right.  new fertilizer, and a good blend of peat moss (that I sift into powder myself), vermiculite, sifted compost, and fine sand.   It works for me and I fill a large trash barrel with it.  Which is the amount I use up each Spring.



I sure won't be bored before Spring!

Daffodils 2

So I had daffodils in some tubs and meant to replant them last Spring after they bloomed.  But didn't.  I got busy with other stuff.

I tipped the bins over last week and picked the bulbs out of the soil,  Wow, those bulbs loved the rich soil!  Most had multiplied into 4.  Well, I have this new island around a tree and boulder in the front yard.  About 40'x20'.  I tried planting Astilbe there, but the deer just kept pulling them up (couldn't eat them, but kept trying).  Well, I know they sure can't eat daffodils (toxic to most mammals). 

The bed was covered with large saucer magnolia leaves.  I raked them just off the bed so that I could use my little electric tiller (which is great for small areas) to kill the weeds.  I have a large tiller, but it isn't good in small areas.

I planted those recovered 100 bulbs in the front island. 

I am now utterly worn out.  I have put away all my planting tools.  I am done for the season...

And actually, this was several days ago.  I am really done.  I've pushed myself to my limit, getting inside before sunset and sitting in a chair exhausted.  I get muscle cramps from all the digging and bending.  I've been getting my hands clenching up, cramps in my legs, stitches in my sides.

I AM DONE FOR THE YEAR!

But oh next Spring is going to look SO wonderful...  It will all have been worth it. 

Daffodils

I wasn't just working on the hose reel platform this week.  I was planting daffodils too.  And a LOT of them.

The original plantings looked like this...

One quarter daffodils...  I decided to complete the circle this fall (avoiding where I had planted tulips and hyacinths in vole-proof metal cages) 2 years ago.  I ordered 500 daffodil bulbs and they arrived 3 weeks ago.  I looked at them all and said "OMG, WHAT was I thinking"?  How could I ever plant so many?

It took 2 hours per day for 4 days.  First, I thank technology for drill augers!


Attached to an electric drill, you can get fast holes  for bulbs to go into.  They even cut some small roots and lift out small rocks.  It takes some work, but works better than those cylinder push-down bulb-planters in rough soil.

I kept track of where I planted bulbs from day to day by surrounding the planted area with bright yellow nylon marine rope and leaving the closest row of bulbs unburied.

And I had to do some exploratory digging.  I had covered the tulip and hyacinth cages with cardboard cut to size and pinned with tent pegs.  And the whole are was covered with black plastic sheeting to smother the weeds and keep the bulbs dry (which they like).

But even then, I was surprised to discover that some of the cardboard markers rotted and some were loosened when a windstorm came through right after I removed the plastic.  Sad timing.  But the tent pegs were still there and I spend a whole afternoon finding them.  Which allowed me to replicate where the cardboard covers had been,

The recreated covers looked like this...

I planted all the new daffodil bulbs around the cardboard covers the other 3/4 on the bed.

Almost.  I came short a 6'x5' section at the end.  Home Depot had 40 bulb bags on clearance.  Most were blends and I didn't want THAT!  But I found ONE bag of one kind (King Alfred) and JUST barely filled up that last area.

Bed Complete!

But I had some in some tubs that needed a permanent space.  That's tomorrow...

Hose Reel 6

So the post is in and solid.  The metal bars are assuring it stays upright and level.  Time to attach the hose reel...

The hose reel has 4 front screw holes and 4 back ones.  I used 1 1/2" x 3/8" lag screws in pre-drilled holes.  I put rubber hose washers on the bottom and fender washers (large washers with small holes) above those and drove the galvanized lag screws down tight.  THOSE aren't going to come loose!

The hose reel turns to the left...

To the right...

And rolls up the hose...

It's a bit ugly because it is coldish outside and the hose isn't as limp as it will be in Summer.  But as a test of the system, it is good.

After testing the "reeling", I used it to water the newly-planted daffodils.  The hose came off the reel beautifully from any angle.

Tomorrow, planting daffodils...

Hose Reel 5

I had a hose hanger on a 4x4 post there, and pulled it out.  Then used a 6" spade and a post hole digger to deepen and enlarge the hole.  That was easier than I expected.  The soil was quite good.  The bottom foot was mostly clay, and I saved that for backfill.  Its stronger.

This picture shows getting down 20".  I got down to 24" but the picture failed.  I usually take several of each event and all are good, but not this time,  Figures...

But I got the post into the hole and stood it upright.

I backfilled from all sides gradually.  I didn't have a good tamp available, but realized the D handle of the shovel worked well.  I'm good at using whatever is near at hand.

I packed that clay soil hard! 

Then put a level on the top and made some slight adjustments.   Tamping hard on one side adjusted the post to perfect level.  And then I set metal bars on either side (anchored with cinderblocks) to hold it it place.  Then I used a piece of 4x4 post (more useful scrap) to really pound the clay soil around the post.

The top was utterly level!  I left the metal bars in place to assure the post didn't move while I soaked the soil  and tamped some more.  

That post ISN'T moving!

Tomorrow, attaching the hose reel to the platform...

Hose Reel 4

So the post and turntable are all set for installation.  I released the bench vice holding it and went to lift it.  I couldn't lift it!  It was TOO HEAVY!

I had to drag out my dolly.

It took 5 minutes to drag it out of the basement to the installation site!  Clutterred basement, rough ground...

Tomorrow, the hole for the hose reel post...

Hose Reel 3

The rotating hose reel project has been a real challenge.  Every time I think I has something right, it's wrong.

The original plan had a 6"x6"x5' post (a leftover from when the deck was built 3 years ago).  Leftovers are always useful for SOMETHING eventually.  That part stayed. 

I was thinking that the turntable construction needed 12" boards across it for stability and some other boards as braces on the sides. 

But it occurred to me that metal angle brackets would to that side strength.  And then I realized the more metal brackets could replace ALL the boards.  And a lot easier to install...

So what was first a rather complicated structure of 12" carriage bolts and 10" lag screws became a simpler build of 3" deck screws into angle brackets. 

So I dragged the 6"x6"x5' post into the basement and clamped it upright in my bench vise.  I needed two 3" angle brackets on the front and back and two 4" brackets on the sides.

But then I decided that having 2 brackets on each side of the post was even sturdier.  One is good, two are better!  I've never seen anything I can't over-build...

I had some 3" brackets and screwed them in.  I had to buy some 4" brackets.  To my surprise, all the DIY stores were CLOSED on Thanksgiving day.   They are even open on Easter!  Walmart was open though.  But they had only 3" brackets.  So I got the 4" ones Friday.  

Reality is cruel!  When I went to attach the 4" brackets, the screws hit the 3" bracket screws!  ARGH...  I don't have a picture of the 3" brackets screwed in, but the dots mark the spots

I decided to offset/lower the 3"brackets  by adding a strip of 1/2" plywood cut to size (more good use of scraps).  That caused all the attachment screws to miss each other.

 Here, you can see the plywood strips, and brackets successfully attached...  4" ones here...

And 3" ones on the othe sides.

Note how the bracket screw holes are now offset from each other...

The post, with the turntable top is now complete, and has strong as can reasonably be made!

Tomorrow, installing the post outside...

Hose Reel, Part 2

The turntable drove me completely crazy!  I watched 3 youtube videos about how to install them and none made much sense.  So I went back to the workbench and turn the pieces around in all directions seeking some way, seeking some understanding.

Think of it this way.  Put a slice of ham between 2 slices of bread and THEN put mustard on the ham without lifting the bread or pushing it in sideways...

I went crazy!

I attached the turntable to the top and bottom pieces of wood in all possible ways.  I even considered the turntable was sold cheap because it was non-functional.  But I knew it wasn't.  It was MY failure to comprehend the one BIG HOLE.

When Sir Issac Newton was trying to figure out the orbits of the planets, he tried many geometric shapes.  And he hit on the right one, but made a simple math error and rejected it.  Looking back later, he figured out his error and solved the problem.

I looked back too.  And realized I had it right once but didn't realize it.  Not that I'm like Newton, but we all make mistakes and find we were right at some point and didn't realize it.

I figured it out...

I can't possible explain, but I could show it.

All I can offer is some pictures...

IT SWIVELS, IT SPINS!  There are a lot of wrong holes in it, but it WORKS!  And with new wood, I could do it again better.  But it works.  I got mustard in the sandwich without lifting the bread, LOL!

I bought heavy duty lag screws to attack the hose reel to the top piece.   I drilled the holes to attach it.

But before I do that, I need to create a solid platform to attach it to the existing 4"x4" post.   More of the same size scrap pieces glued and screwed to the post and cross pieces across those.  But that's another day...

My friends say I "overbuild" things.  But my stuff doesn't fall apart after a few years...  I would have designed the Pyramids just as they are...  LOL!

Wait til you see the finished product...

Hose Reel

I bought a hose reel a few weeks ago, not sure exactly how to attach it to anything.  The instructions say it MUST be attached to a wall or affixed to the ground.

HAH!

I decided I wanted it to swivel, so that I could pull the hose off in different directions.  My initial thought was to put a 2" metal pipe in the ground and set a 3" PVC pipe on top of that so that would rotate on the metal pipe with some support structure to hold the hose reel.

That got kind of complicated, and PVC pipe is not the sturdiest stuff.  So I let it sit in my mind a few days.

I was shopping for other stuff at the DIY store, and noticed a little 4" turntable (aka Lazy Susan) and thought, "Hey, I have a 12" one of those I bought at a yard sale years ago because I thought it "might be useful".

But I couldn't figure out how to attach it to a post AND attach it to the hose reel.  The internet is an amazing thing.  Ask the RIGHT question, and some other people know the answer and even do a video showing how.

I had figured out how part of it worked.  There was a big hole in the bottom that allowed access to all the smaller holes.  But I still couldn't see how to get at both the top and bottom since it seemed the holes got covered by a board no matter what I did.

Sneaky tricky stuff, but it all had to have a purpose.  The big hole was the key.  And not attaching the hose reel directly to the turntable.  The video I watched showed about using the big hole to allow access to all the other small srew holes.  I got THAT right.  But then it showed attaching 2 square boards to the top and bottom and THEN attaching your "whatever" to the top baord.

DUH!  Slapped forehead.  And the video even expected that.  It said "you can't do it the way you want to directly".

So I needed 2 boards suitable for outside conditions.  Well, I could buy a sheet of pressure treated plywood and cut it to size.  Or use stuff I had.  I didn't have anything 12" wide.  But I had scraps of 2"x8" boards leftover from building the framed garden beds 2 years ago.

But I had to attach 2 pieces of it twice together (a top and a bottom).  Gluing wasn't sturdy enough.  But I had a "biscuit joiner" I bought 20 years ago and had only used once.  AHA, I had a reason to use it!  A biscuit joiner cuts oval shapes in the edge of a board and you gkue precut ovals into the cut slots.

I ran the scraps of wood through my planer to make the surfaces flat and exactly the same thickness, used the plate joiner to cut slots in the edges and glued in the biscuits (ovals).  Clamped them tight and held them flat with clamps and weights.    The wood ovals swell up from the moisture in the glue and the squeeze-out gets between the boards and hold even more.  He stuff makes 2 boards are solid as one larger board.

Naturally, I forgot to take pictures (and I had my camera in my pocket)!  But I can replicate some of it to make sense of all this text.

And that is where I stopped for the day to bring some deck plants in because of the first hard freeze of the season.

More later...

Veterans Day