Uncovering New Plants

I have this spot I thought would be perfect to Astilbes.  I love Astilbes.  They want half-shade, and the spot was right.  I had old ones there in a corner, so I added 25 more last April.

I have a grass-weed that takes constant pulling/digging.  I get rid of it in one spot and it is spreading in another.  One day I will get the last one (making progress actually).  So it was overgrown where I planted new Astilbes in April.  They had to go...

The orange flags mark where I planted the Astilbes when the ground was bare.  I went after the grass yeasterday.  I got it down to this.  The grass came out relatively easily.  But those were the shoots on deep underground runner-roots.  Still, you can only pull up what you can get at.

And I did get mostly roots pulled up with the grass-tops!  A full bushel basket of them.  It looks much better now.

The grassy-looking plants mid left are actually flowers.  Crocosmia.  Lame small orange flowers for a week.  I may just pull them, but I hate to waste a flower.  Maybe I'll dig them up in Fall and try a new space for them.  They want more sun anyway.

The spot I have the Astilbes in is mostly shaded.  But it gets serious late afternoon sun, and they don't like that.  At least yesterday after I pulled up the 16" tall grasses, they had some shade.  After that, Mr Sun hit them hard and they wilted.  But it was only for 2 hours.  I hope they adjust.  Otherwise, I will be moving them in the Fall (and I have a spot in mind).  It depends on how well they do this year.

They looked better after some deep watering and with the landscaping flags removed...

I made a slight mistake planting the new ones.  I thought I knew where the established few were and where the Crocosmia were.  Well...  not quite.  I planted some of the new Astilbes among the established ones and among the Crocosmia were.  I'll move them to the front bed.  The corms are tough and tolerate moving.

The Baptisia will give them some shade soon.

I need to stake them though.  They flop over.  The Astilbes loved their shade, so I'm staking the Baptisia and tying them loosely upright this year.  I'm almost actually keeping up with gardening work this year.

I've been outside almost 4 hours per day for a few weeks now.  It shows.  I've never been so nearly caught up with gardening and yardwork before.  Yay!

Various General Work

Some days are just catching up on small things. 

1.  I spent an hour pulling grass up from the new front yard island bed.  With 3" of Fall leaves topped with 3" of compost, the weeds don't have a solid grip.  But they were lots of small weeds and it took a while.  Better now than when they good good roots into the soil...

2.  The pole beans and cucumbers are up.  But there were a few spots where a seed didn't grow.  So I soaked a few replacement seeds in water for 4 hours and then planted them. 

3.  I can't BELIVE I forgot to plant a cherry tomato seedling with the regular ones.  So I planted it 3 days ago and shaded it from the direct sunlight for 2 days.  It wilted a bit the first day but is happily hydrated now. 

4.  I have a 2'x8' framed bed against the southern side of the house.  Hottest part of the yard.  I planted 2 blocks of bico9lor corn there today.  One matures 2 weeks before the other, so I'll have a staggerred harvest.  And I'll plant 2 more blocks in 2 weeks, for more staggerred harvest.

5.  The Meadow bed is full of several dozen large bright yellow flowers, some dozen multiple flowers in reds/pinks.white, some white daisies, and some small blue flowers.  The plants are listed on the packet; I will look them up so I know what they are called.

6.  The Hummer/Bee/Butterfly bed is too new to have flowers.  BUT, on a whim, I scatterred old veggie seeds in there too.  I am harvesting the best sweetest radishes ever!  And there are a few corn plants coming up.  It is going to be a weird bed this year.

7.  I've been growing bok choy to harvest young for stir fries.  Some are old even to flower.  I just discovered that the pre-flowering heads are like brocoli, only sweeter.  I coukld grow them just for THAT!  But I also like picking the young leaves for the stir-fries...

8.  Got one major project done I meant to do last year and waited too long.  And almost waited too long this year.  The Spring Bulb bed has daffodils, tulips, and hyacinths.  The Tulips and Hyacinths are in wire cages to protect them from the voles.  But there is unused space between the wire cages and I want to plant daffodils to fill the bed (except for the tulip and hyacinth cages).

So I had to mark the spots of the tulips and hyacinths.   It was a close call.  The tulip leaves were still just barely visible.   I thought because the tulips bloomed after the daffodils; the leaves would last longer.  Nope.  I had to to some careful searching to find the spots.  I did. 

Which led me to how to mark the spots.  Well, first, I found the cardboard cutouts I used to make the cages.  12'x14".  Then I had to find cardboard to cut to size to place on top of the cages (so I wouldn't auger in to them in the Fall while planting daffodils around them.

An aside...  I keep things the are of similar size because they seem useful that way.  A dozen liter juice bottles, a dozen plastic jars that hold mixed nuts, etc.  Well, I buy the same wine by the case and I had a dozen of them stacked up in the basement (thinking they would be good for storing stuff fitting together perfectly in tight spaces).

Well, guess what exact size they were with a wide side and flap?  The size of my tulip and hyacinth cages!  And I have a weird curved linoleum cutter my Dad made.  It sliced right down the corners of the boxes perfectly. 

And guess what I also had?  Fifty 10" tent stakes!  Perfect for holding the cardboard down.  I cut them to size, put the debris in the recycle bin, poked a hole through opposite corners with an awl, and carried them all outside.

It was hard to find the remnants of the tulip leaves, but I had pictures of the bed from 2 directions from the blooms last year.  Between the few leaves and the pictures, I set down the cardboard covers and stuck the tent stakes in the holes to keep them in place.

Then I weed-whacked the whole area.   Why?  So that I can cover the entire area with black plastic to kill all the weeds.  The bulbs won't care; they don't like rain while they are dormant.  When the weeds are dead, I'll uncover them in Summer so the bulbs won't overheat (they are shaded all day now).

9.  All this work has been awkward.  I like to keep my kitchen knives sharp.  Stele them once a week to straighten the edges (they curl with use), and sharpen them every few months.  You know that test about tossing a ripe tomato at a sharp knife and it cuts the tomato in half?  Mine do that.

It does that to fingertips too.  I'm careful.  I have brushes to keep my fingers away from the sharp edges while I clean them.  But OOPS!  I cut my fingertip badly a week ago.  I hadn't seen that much blood in 30 years.  It was 15 minutes before enough pressure even stopped the bleeding.  Fortunately, I coagulate fast.

Anyway, I finally managed to get enough coagulation to put a bandage on it.  I have some of that triple antibiotic ointment on it first, then a large bandaid, then some adhesive cloth bandage along my finger to hold the bandaid in place. 

It HAD to be the index finger of my right hand of course.  The MOST inconcenient finger for a right-handed person.  Makes even putting on my velcro-strap watch difficult, never mind tying shoes.

But I may be a bit lucky there.  I think I was a natural lefty, taught to be right-handed in the 1950s (a common practice in the US, then).  I still do some things with my left hand naturally and deliberately do some things left-handed for practice.

It has certainly helped. 

10.  Making progress on the compost bin.  Nothing to show, as I was just collecting boards and posts for cutting and assembly tomorrow.  I looked at the boards and posts I already had and adjusted my design slightly to account for those.  Might as well use up what I have rather than buy new boards!  I'm always flexible about designs.

Compost Bin, Part 2

I set the work aside for a couple of days to catch up on weeding while the weather was cool.  But it hit 90F yesterday, so it was a good day to work in the cool basement.


So, I mentioned using the tenon jig to make half-lap joints...


This is the jig.

It holds a board upright to cut a large slot high.  I apologize, this picture was a reconstruction and the saw blade was not as high as in reality.  Sometimes I forget to take pictures during my work and have to recreate them.

I can make tenon cuts in 4' boards.  I could do 5' by removing a ceiling tile.

There was massive sawdust everywhere.  I had to wear a nose/mouth mask! I tried wearing glasses too, but the mask directed my exhalations up and fogged the glasses.

 Here is the table saw blade going through the upright board.  There is a lot of wood being removed, so I had to push slowly.  Its a 220v tablesaw, so there is a lot of power, but I still don't like to push too fast.

The 10" saw blade only cuts 3" (part of the saw blade is below the table).  So I get only a 3" deep cut.

I tried a few ways to complete the cut.  A regular saw took too long, a flush-cut saw made an uneven cut (and was slow).  The Saws-All did the job wonderfully!  I love electricity over muscle-power everytime!

The weight of the saw is perfect for cutting down the right distance.  The cut part just falls off.

So then I was ready to assemble some frames.  I had everything ready.  One drill for pilot holes for the screws, another drill for counter-sinking the screw heads (to avoid splitting the boards), exterior glue,  a rag to wipe off squeezed-out glue, a square, and a tray of 1.5" square-drive screws (I love those things).

Here is the first assembled frame.

Then to add the wire mesh sides (to hold the compost in).  I used an electric stapler with 9/16" staples where possible.  Pressure-treated wood can be rather hard even though it it's pine, so sometimes the staples don't go all the way in.  That means some gentle patient tapping with a hammer.  Sometimes, they won't go in at all, so I also have some heavier-duty staples that have to be hammered in by hand.  That takes some effort to get them in straight.  Fortunately, with pliers to hold them straight and a patient hammering, I got them in.

So here are the 1st 4 frames.  These are the 2 backs and 2 sides.  I need to make a 5th, but until I make and set in the front posts (yet to be constructed) I don't know the exact size to make.  Some things just have to be "fitted" at the end.

The next part is to make the back corner and front posts.  The front posts need to have spaces for slats to fit into.  I could cut slots in posts, but it is easier to build posts from several boards to create slots rather than cut them. 

I'll show that next time.  Meanwhile, there are some old deteriorated beds where I want to install the new compost bin, so I need to demolish those first.  And there is a shrub I want to save from there. 


This isn't the best time of year to move a shrub, but I don't have much choice.  I think I will take a dozen tip-cuttings and try and root them indoors before digging the shrub up.  And I'll make the rootball extra large to give it a best chance to survive the transplant shock.

Tomorrow is predicted to hit 92F, so I don't think I want to do serious work outside then, but I'll break up the framed bed it is in and get that part done. 

And I have work I can do inside or outside in shade.  I really try to do as much work as possible in the shade.  LOL!

Mothers Day

In Love and Remembrance...

Compost Bin, Part 1

Well, I got started on the compost bin I mentioned a couple days ago.  And it was about time!  I originally made a quick-and-dirty one not long after I moved here.  It was just 6 upright posts sitting at ground level with boards nailed around them and a divided to make it 2 bins.  Needless to say, it didn't last long.  Nails don't hold, pitchfork activity and leaning on the posts made it tilt over, boards came loose.  It wasn't a total failure; it did function for 10 years.  But I expect more than that.

I built a better one for a friend.  Posts set in the ground with cement, screws, removable angled fronts.  I always do better work for others.  For myself, I take shortcuts.  *sigh*

So I bought one of those big rotating barrels set on a stand with a handle to turn the barrel.  That lasted 10 years, sort of.  The gears to turn the barrel broke after 5 years, then a side can loose.  I was leaving grass clippings on the lawn, mower-shredding fallen leaves into the lawn anyway, so I used the barrel just to let kitchen scraps decompose.

But I'm changing back to making real compost again.  So I looked up a couple plans online, mixed some features together, and improved on them.  It has 2 bins each 4' deep and 4' wide and 3' high.  The 2 back, 2 sides, and 1 divider are made of five 4'x3' frames of 2"x4" pressure-treated lumber with 1/2" wire mesh attached to the inside edge.  Well, the divider is a little smaller to fit between 2 posts.

The 5 wire mesh frames are made with half-lap joints.  They aren't elegant joints, but they give plenty of surface space for gluing and screwing so they are very sturdy.  This isn't living room furniture; strength is better than appearance, LOL!


You can dado-cut half lap joints, but I have a tenoning joint gadget I've never used and that makes smoother cuts, so that's how I'm doing it.  I'll show actual construction pictures later.  But it takes some effort to make the half laps fit together perfectly.  You can't just find the center of the board; the saw blade removes material.  And the tenoning gadget was new to me.  Fortunately, I had scrap pieces of the 2x4s and got the cutting depth right after only 3 tries. 

The half lapped frames will also have a diagonal brace inside the frame.  I'll do that the easy way.  When the frames are glued and a perfect 90 degrees (clamped to some squares I have for that purpose), I'll put in screws for long term holding.  Even exterior glue doesn't hold forever.  THEN, I'll simply put a 2x4 under the frame, pencil the cut, and use a taper jig to make the brace fit into the corners.

Then I'll attach the brace with pocket hole screws.

I bought a pocket hole Kreb jig a few years ago and I love it.  Talk about SOLID!  I have tightened squeeky floor joists in the basement and loose deck posts. 

So my compost bin parts are modular.  Pre-constructed 4'x3' frames to be attached to in-ground posts I will space as I go.  Hey, I know my likely failures; if I dig the post holes first, they will be off a couple of inches by the end.


The posts will be set a foot deep.  With my clay soil, cement is not needed.  But I will use a tamped-down brick at the bottom of each hole to prevent settling and frost heave.  With the posts set in a foot, on firmly-settled bricks, and diagonal braces in each of the back and side frames, this compost bin will not tilt over.

Which leaves the front...  With most compost bin designs, you have to reach over the front to spear the material to shift it from one bin to the other (to keep it aerated and mix it well).  That gets awkward and tiring.  I build my friend's compost bin with angles slats set into cuts in the posts, but that weakened the posts (we had to fix that after 5 years). 

This time I am constructing posts for straight up slats to drop into.  I am sandwiching a 2"x2" post between wider boards to create a slot for the removable front slats instead of cutting one and weakening the posts.

The idea is that I can just lift the slats up through the space between the wider boards for easy access to the bin contents.  And the slats will have 2" long spacers under each end for aeration.

The top will come last after the whole thing is installed.  I know all too well from past experience that planned measurements can get off more than one would think on rough projects like this.  The top will be custom-fitted to whatever the exact constructed size of the bin is.   And quite frankly, I want to see the finished compost bin before I decide what kind of hinges to use.

Tomorrow, pictures of the half lap cutting, and possibly the first assembly of the back and side frames...

Yard Work 3

Mosquitos are a problem here.  The Asian Tiger Mosquito showed up here in 1999.  The Authorities said it wasn't here yet.  It stunned one back then and kept it intact in a small jar in the refrigerator and tried to tell the Dept Of Natural Recources and the local University that I had one, but no one seemed interested.

So, naturally, a YEAR later the local newspaper headlined "Asian Tiger Mosquitoes Found In Maryland".  Yeah, I knew that. 

Anyway, I have been fighting them ever since.  The little bastards are active in daytime and are hard to detect on your skin.  I happen to be good at detecting them on me, so I have probably killed more of them than the average victim.

This year, I am fighting back.  I'm trapping them.  Well, not the adult females, the offspring.  They lay their eggs in water.  There is a bacteria (Bacillus thuringiensis) that kills the larvae.  It comes in various forms, but I like the small Bt doughnuts of it that you just drop in standing water.

I  set out 5 pots of water with the Bt around the yard last month.  I set one pot without it.  When I see larvae in the untreated pot, I know the the females are laying their eggs in the treated water too.  I dump the untreated water pot every 2 days.   The treated water pots never have live larvae!

I found old black plastic pots that fit a gallon food baggie perfectly.  The dark pot makes the water look good to the female mosquito  The orange landscaping flag is so that I don't lose track of where they are.  The Bt has to be re-added once each month.

Getting the first few generations killed makes a BIG difference.  Already, I can go outside and find only a couple flitting around me and I swat them against my shirt very fast.  Fewer and fewer of them.  They don't travel far, so most of them here are from here.

Two years ago, I could hardly go to the mailbox without a bite.  This year, NONE! 

Yard Work 2

Building a compost bin...  My original 2 section compost bin died years ago (falling sideways and such).  Well, it WAS over 25 years old.  I still dump kitchen scraps in it, but I decided I was mostly just feeding possums.  So it was time for a new one.  And in a new location.

My new garden enclosure resulted in an unusable spot north of it.  Perfect place for a new double-bin compost bin.  So I looked up some plans for covered 2-bin compost bins.  I didn't find one I liked.  HURRAY, I get to design one myself.  I'll build anything great I find, but I love building something better.  I spent time this past Winter doing that.  Came up with a nice one.  It had 1/2" hardware mesh sides for aeration, was designed for 5 identical square frames of pressure-treated lumber, and a hinged top.

After looking at the design this week, I thought of changes.  I sketched it out Saturday, improved it Sunday, changed it again, diagrammed it on graph paper, and bought most of the pieces yesterday.

It is built of five 4'x3' frames of 2"x4" pressure-treated lumber with diagonal braces to prevent leaning.  The front has 1"x6" boards that slide down in slots in the front for easy removal and access to the compost material for turning.  The corner posts are set down in the soil a foot deep for added sturdiness.

The front posts are interesting.  To make slots for the boards to sit in (for easy removal for access for turning the bin contents, there are 2 ways to go.  One is to cut slots in a 4"x4" post.  I have the equipment to do that, but my past experience is that that weakens the post.

The other way is to construct a slot.  A 2"x2" between two 2"x4" boards makes a nice slot too and is easier to build.  And I already have the pieces to do that.

So here is my diagram...

I wish I could show it better.  Scanning a drawing is always frustrating for me.  I probably have incompatible equipment.  It took 20 minutes to get THIS!  😂😣

I'll answer any questions about it...

Later today, I'll start cutting the boards I bought to the sizes I need.  Some of the joints are "half-laps", so I'll finally get to use the tenon-cutting jig I bought years ago.

The good thing is that I am finally getting around to a project I have wanted to build for several years.  Most years, this project stayed low on the priority list.  Now it got to the top.  I must be catching up on things!

YAY!

Mark

Yard Work 1

I finally learned the name of the invasive vine that has been creeping into my yard from the neighbor's yard.  It's Periwinkle.  I thought Periwinkle was a small plant like violets!  But a couple of posters on a garden site clued me in, and when I looked it up, there it was.  I can't believe a week of searching "invasive vines" didn't help me find that out myself. 

It is apparently hard to kill.  Deep resilient spreading roots, leaves that don't absorb water, tolerant of many soils and sunlight.  I even have some I put a trash barrel over last summer; the entire vine is white but won't die.  They are surviving by nutrient spread from uncovered vines.

I weed-whacked them last week.  That should weaken them for a while.  But it seems there are only a few ways to eliminate them.  Digging the roots out 2' down, covering them in black plastic for a couple years, and using herbicides.

Digging down that far needs heavy equipment and the space is too tight.  I can't cover them all with plastic as they are among plants I want to keep.  So that means herbicide.  And it means an oil-based herbicide.

I try to stay organic.  Not certified, but in general practice.  So in the open areas it has invaded, I will spray carefully.  I have a large cardboard box I have cut the bottom out of and made a small hole in the top.  I will spray Triclopyr into the hole, let the box sit sit 5 minutes and move it to the next spot (wearing latex gloves and a mask).

Then I will cover the area with black plastic (I have large rolls of the stuff).  For the individual plants in the flower beds, I will apply it with a 1" brush on leaves.  And since I'm going that far, I will use the box on the poison ivy and the english ivy ("in for a penny, in for a pound").

Flower Pictures

After the Spring Bulbs are gone, I'm offerring a cascade of pictures of them.  Just to share and remember.

Gardening And Yardwork

I had a successful day today - I planted 6 annual sunflower seedlings!  There was a lot more to the day's work, of course, but by the time I planted the sunflower seedlings, I felt I was done.

For starters, the temperature reached 88.5F according to my 2 different brands of digital wireless outdoor thermometers*.  In April.  In the shade.  And I didn't spend much of the day in the shade.

My PRIMARY desire for the day was to plant the sunflower seedlings.  For some reason, I sow 6 sunflower seeds every Spring, and never get around to planting them before they are too leggy and weak to thrive.  They are always "last on the list".  Partly, I never have a really good spot to put them.  Well, this year I did.

I have mentioned before that I set up 3 edged beds in the back yard.  One is for wildflowers, one is for  Spring bulbs and daylillies, the last is for bee/butterfly/hummingbird flowers.

In the center of that last (middle) one (only 10' in diameter), I wanted to plant sunflowers as a centerpoint.

But I had trimming to do first.  I mowed the lawn 2 days ago and the more constructed beds I create, the more trimming there is.  My new Ryobi 40 battery-powered string trimmer does a grand job!  But you have to USE it, so I did that first to get it out of the way.  It was a lot more work than I expected.  The trimmer battery last about 40 minutes; I used that up and set it to recharge.



While I was waiting, I took my hedge-trimmer and dead-headed all the Spring bulbs, and I have more bulbs than I used to (when I could do that with my sheep-sheers).

Still with time before the string trimmer fully charged, I caught up on making more plant labels.  I found a great deal on metal plant labels last Fall and got 120 for 50 cents each.  Plastic labels just don't last.  After that was done for all my existing crops and some specimen hostas, I went back at trimming the yard with the string trimmer.  It takes longer to trim than to mow the whole yard!  And I was using it to cut down an invasive vine, an invasive self-sowing spreading loosestrife (Lysimachia Firecracker) shipped to me in error as a Coreopsis, and some self-sowing Salvia(?) perennial I regret ever planting.  I'll keep cutting them down until they all die!

I was pretty much used up for the day, but remembered the sunflowers.  I HAD to plant them, sweaty and tired as I was.  My idea was to set a 1' diameter 2' tall wire cage in the center of the bed and plant the sunflowers around it attached to the cage.  I measured out the center and set the cage there with some stakes to hold it in place firmly and used an auger to drill 6 holes around it.  It was awkward reaching around the cage to set the seedlings in while not stepping on newly-emerging hummer/bee/butterfly seedlings, but I managed it.

I have a couple hundred plant clips (another good deal I found, and endlessly useful), and supported the sunflower seedlings  to the cage with the clips.  The clips are about 1" around, so they wont restrict the stems.


Support 2' high should help the sunflowers stay upright, but if not, I can attach a 2nd cage on top of the 1st.  Yes, I should have just planted the sunflower seeds directly and they would have been sturdier.  But I always try to rush the season by starting them indoors.  Next year, I will sow them direct.

But for once, they are planted and have a chance.